How do you adding new Network in
Internet Rex Mailer.
================================

1.
First start up rex config setup by start rexcfgw(/l/o/d)

Then yo go in to the Address Manager.
You is see 3 choices her:
Adress manager
Zone matching
domain setup.

You start with setting the new networks domain to start with.
So go in to domain setup menu.

-----------------------------------------
Domain setup menu:
Use her your keyboards insert key to add the domain for the 
network.

You will see:
 Zone   Domain
-------------------
now write the networks zone number (ie. 111) hit return
Enter by type in the networks domain name, tis shoudl habe be given 
you by your new networks coordinatot the OC/ZC. (ie. stn)
Hit then Enter or Retur to go on to the next input.
If more than one netwrok to add then ad the next network as over here.

If you if and no more network domain to add in, then easy use esc key
to you is back to se the 2 choises again.
-------------------------------------------

Now go to Address manager here:
Here will you now should see following.

Man address
System AKAs

Move marker down to System AKAs 
and use return to go in to it.
You should see > arrow point to a empty place.
Hit your return key and the empty palce is change in look.
Now type in yor new node number here. (ie. 111:4523/654)
Hit return so save and sure it is done and got in.
Then use escape easy to you is back with the 3 choises.
----------------------------------------------------------

Go here to Zone matching menu choise.
You should here see:

Zone matching:
  Zone    AKA
------------------
Your first input should be here allready, so:
Move the cursor/maker down to the button of the menu.

Use now her either Return or Insert to start to add the
new Zone and Aka.
First The zone (ie. 111) return 
then will you see some node numbers, and your new node number
should be here.
Move the marker to it and use return to put it in.
It give you the look with the zone and nodenumber.
Be sure that the zone and node node number math together.

So now easy escape ket out to the 3 choises.
Easy escape out to Irex Main Menu.

Go in save and sure to quit program and use Yes to save settings.
It should now have make that yoru have the first thing configured
for your own setup.
--------------------------------------------------------------------

2. Setup and Configure your uplink informations.
------------------------------------------------
Start rexcfg again (the last character can be w, d, l or o.
In the main menu, go to Node Manager choise.

You  should and will see, your first uplinks node-number and Name:
Example look:
  Node manager
    1:261/38  B B Y   Janis Kracht

--------------------------------------

Now use insert on your keyboard to add your new uplink.

  Node information:

 System adresses
 Sysop's name  

 Node active         Yes
 Outbound messages   Don't toss outbound

 Inbound messages    Don't toss inbound


 File bundling
 Connection information
 Node's statistics
-----------------------------------------------

System adresses will be marked, so start with this.
Now use return og insert key.

  Node adresses:

Adresses > (Type in yoru uplinks node number and then return)
The marker > will jump to new line.

If not more aka(s) for your uplink, it your finish with it here.
So easy eascape one time back.
Your new uplinks node number will you now see after System adresses.

Move marker down to Sysop's name and use insert or return to this.
Type in here your new uplinks name.
Then easy escape back to the menu.

Go then now to Outbound message in the menu!
Use Return to you see toss Binkp site (for binkp connection).
This should give this in the Menu:

Outbound messages   Toss to a BinkP site
  Configure

Move the marker to -> Configure !

 ===> | Toss to/from a BinkP site | <====

 Site's address
 Site's hour          0.00-24.00
 Connection timeout   60 secunds
 Block size           4096 bytes
 Use NR mode          No          Use CRC mode   Yes
 Use CRAM-MD5         Yes         Use MD5 mode   Yes
 Default domain
 =====================================================

Start here with Site's address (it is your uplinks binkp hostname).
Use return key to start her.
Type in your new uplinks hostname. (ie. filegate.net) or ip address (ie. 11.33.44.55)
It is mostly used is the hostname.

Use return key when this is done.
move the cursor and marker to >> Default domain. 
(it is the domain for and of your new added network your shall use here.)

Type it in then (ie. stn ) and then return key be sure it got in.

Now use easy eacape key back to the other menu.

You shall now be in ==> Node information Menu <===

Move marker to -> Inbound messages
Use return to you have and see:

Inbound messages  Toss from a Binkp site
   Configure

So when done this move the marker to > Connection information, use return:

 =====> | Connection information | <=============

 Packet level passowrd   ********
 Encryption password     **************************

 Session password        **********
 Rexfix password         *********
 Send notify             Yes
 Send help messages      Yes
 Secure connectoion      No
 Reliable connection     No

 ==================================================

Move the marker to and go to Session passwrod, and use return to start.
Type your Binkp Session password for yu new uplink. Then return to save it.

Move the marker to Secure connection and use return.
The line will change to be:
Secure connection  Yes

----------------------------------------------------------------

Use then easily escape to you is back in the Rex Main Menu!
Move the marker down to > Quit program.

Then use return and then Return or Y to save the setup.

End then with cd in to your Irex directory and do this!
copy and zip all your *.rex files.
zip/pkzip irexback.zip *.rex
It makes you to get config backup of all your irex configs.

You is ready with you new added network now!



